PIC Mapping for : for wiring details, refer to schematics on the website. ------------------------------------------------------- PIC1: ***************************************************************************** Version 1.0 - preliminary - 29.06.2007 wiring finalised 30.06.2007 04.07.2007: programming session with Johannes Taelman. Version 1.5 - after debugging midihub board. Board version 2.0 , not 1.6. 05.07.2007 Version 2.0 - MidiHub board, programmed by gwr.07.10.2010. Proton+ compiler. Midi channel: 1 (counting 0-15) PIC1: On MidiHub board - X17.1: GND - X17.2: PIC pin 12 PWM analog output motor movement. Note 58, velo= PWM, Note Off implemented Hitachi Motor - X17.3: PIC pin 13 PWM analog output motor movement. Note 59, velo= PWM, Note Off implemented Pabst motor - via opto relais TO BE CHANGED: ON / OFF only !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Changed gwr. 07.10.2010: now only on/off - X17.4: +34V , power for Hitachi DC motor. Note: Both outputs should be zero on start up. They should also go zero on all notes off commands. lights: (Note ON/OFF) - X11.2: PIC pin 5 Midi note 110 Bajonet 24V/5W front - white - X11.3: PIC pin 4 Midi note 111 Bajonet 24V/5W front - white - X12.2: PIC pin 3 Midi note 112 2 E10 bulbs - 35V/50mA - X12.3: PIC pin 2 Midi mote 113 back spotlight 24V/10W - white - X15.0 GND - X15.2 pic pin 25 Midi note 114 Front lights (LED spotlites) - X15.3 pic pin 24 Mapped on controller 66: Power on off (relais & large indicator LED) - X15.4: +17V - X16.5: AC switch relais Papst motor - X16.6: AC switch relais Pabst Motor Additional controllers: controller 123: all notes off, motor off, lights off. Do not reset controller 66! New in Version 2.0 firmware: Note Pressure implemented on notes 110-114 to set flashing speed if the note is ON. (midi command sequence: 160+k, note, period) ****************************************************************************** PIC2: 28-output pulse only board (positive power voltage: 50V) PC-board version: MidiPulseBig rev.2 - March 2007 Weidmueller connector numbering: 28 midi note 60 front cymbal beaters 27 midi note 61 26 midi note 62 25 midi note 63 24 midi note 65 hi hat beaters 23 midi note 66 22 midi note 67 21 midi note 68 20 midi note 69 19 midi note 70 18 midi note 72 back cymbal beaters 17 midi note 73 16 midi note 74 15 midi note 75 14 midi note 77 tambourine 13 midi note 78 castanet clapper 1 12 midi note 79 castanet clapper 2 11 midi note 80 Ufip ice bell (bell cymbal) 10 midi note 82 -expansion 9 midi note 83 8 midi note 84 7 midi note 85 6 midi note 86 5 midi note 87 4 midi note 88 3 midi note 89 2 midi note 90 1 midi note 91 ****************************************************************************** PIC3: Note+ Velo PIC board: (power voltage: + 17V - GND - -17V) board: MidiPuseHold rev.1, Aug.2004 (same board used for Harma and for Bono valves) cymbal dampers, hi-hat movement 1 midi note 64: damper front cymbal 2 midi note 76: damper back cymbal 3 midi note 71: Hit-hat close 4 midi note 81: Ice bell damper 5 note 57 6 note 56 7 note 55 8 note 54 9 note 53 10 note 52 [EOF]